TigerStop Parts

The Gangstop pusher foot is a flat pushing attachment for the TigerStop. The pushing surface is 10 by 3 inches (25.4 by 7.6 cm). The Gangstop reach can be adjusted from 6 to 25 inches (15.2 to 63.5 cm) beyond the leading edge of the flip away.  

The spring buffer is a flat pushing attachment for the TigerStop. The pushing surface is 6.5 by 3 inches (16.5 by 7.6 cm). The spring buffer reach can be adjusted from 10 to 23 inches (25.4 to 58.4 cm) beyond the leading edge of the flip away.

Every TigerStop comes standard with a Mini Gangstop pusher foot or MGS. This is a flat pushing attachment for the TigerStop. The pushing surface is roughly 4.0 by 0.75 inches (10.2 by 1.9 cm). The Mini Gangstop reach can be adjusted from 5.5 to 23.5 inches (14.0 to 59.7 cm) beyond the leading edge of the flip away.   

Locking Handle (includes handle, bolt, & washer). The Locking Handle is used on various pusher foot accessories.

Note: Locking handles come separately. If you would like to order a locking handle set, as pictured, you will need to order two locking handles.    

This hard plastic trim fits snugly in the T-slots on TigerStop extrusions, and is sometimes used to conceal and protect small cables. U-slot is ordered in 1 foot (0.305m) increments. There are four orange U Slots per TigerStop that travel the length of the extrusion.  

The extended miter gauge is an attachment for the TigerStop, intended for applications requiring a 45 degree surface, sloped away from the cutting tool. The adjustable miter retention clip prevents parts from sliding up the sloped surface as the positioner moves. The clip can be adjusted to provide from 1.5 to 4.5 inches (3.8 to 11.4 cm) of sloped surface. The extended miter gauge reach can be adjusted from 15.5 to 34 inches (39.4 to 86.4 cm) beyond the leading edge of the flip away. 

The Miter Gauge (MG) is an attachment for the TigerStop, intended for applications requiring a 45 degree surface, sloped away from the cutting tool. The adjustable miter retention clip prevents parts from sliding up the sloped surface as the positioner moves. The clip can be adjusted to provide from 1.5 to 4.5 inches (3.8 to 11.4 cm) of sloped surface. The miter gauge reach can be adjusted from 2.5 to 9.0 inches (6.4 to 22.9 cm) beyond the leading edge of the flip away.

The Center Pusher is an attachment for the TigerStop, used for pushing material on center. The push bar adds about 23 inches (58.4 cm) of reach beyond the leading edge of the flip away. The line of force can be adjusted up to 6 inches (15.2 cm) away from the TigerStop beam. The pushing surface is 0.75 by 1.7 inches (1.9 by 4.3 cm).  

The Flip Away is the external portion of the TigerStop carriage. It provides two T-slots for mounting various pushing attachments, and a hinged mount to allow the pusher to be lifted out of the way when necessary. The modern flip away is compatible with TigerStops built in 1999 or later (i.e. with the hinge mount behind the beam).  

The internal carriage connects the TigerStop belt inside the beam to the flip away outside of the beam. Ships assembled with Polymer Linear Guides (PLG). 

The idle end pulley is for TigerStops using a 32mm (1.26") width belt. It is compatible with the Idle End Carriage (IEC2).

Important Information About Ordering This Part:  

• The IEP is not compatible with Idle End Carriages that were manufactured prior to 2016.
• The IEP  will not work in place of the older flanged Idle End Pulley.
• If you are not sure about whether the IEP is compatible with your current Idle End Carriage please email service@tigerstop.com to confirm prior to ordering this part. 

The Idle End Carriage/Far End Carriage is for TigerStops using a 32mm (1.26") width belt. It contains the idle pulley, the pulley housing, and the tensioning bolt. 

Learn more about the Idle End Carriage in the below video.  

The Idle End Cap is a plate that covers the end of the TigerStop extrusion that is far from the motor.  

Dust seal strip helps keep dust and debris out of the TigerStop beam. Dust seal strip is ordered in a single strip in 1 foot (0.305m) increments. Every TigerStop has two dust seal strips the full length of the beam. 

The 20 foot (6 meter) Metal Value pack is for TigerStop machines up to 22 feet overall length (TS20). It includes the following:

-1 ( IOC6-X)

-1 CON5CVR

-1 (CC5-30)

-1 25 foot or 7.6 meter serial cable

The 10 foot (3 meter) Metal Value pack is for TigerStop machines up to 12 feet overall length (TS10). It includes the following: 

-1 ( IOC6-X)

-1 CON5CVR

-1 (CC5-20)

The Pusher Miter is an attachment for the TigerStop, used for pushing mitered material on a double miter saw.  Watch it in action in the below video. 

Please Note: Requires, but does not include, a length of 1010 series extrusion from 80/20 that is equal in length to the OVERALL length of your TigerStop (working length + 2 feet).