Table Parts

Replacement plastic roller for 14" wide plastic roller tables. Part number CR or M3911. The roller sits up 1/8" from the table. 

Replacement steel roller for 14" wide steel roller tables. Part number MR or M3910. The roller sits up 1/8" from the table. 

The Back Fence mounts onto tables and comes in 6' sections. It is often paired with a Back Fence Ruler and used during the Backboard Optimization Process. This item includes the necessary mounting hardware.  

*Note: The Back Fence does not come with TigerStop tables. Those must be purchased separately. 

These brackets attach the legs to the table for all flat TigerStop feed tables. They are incompatible with SawGear tables and with tilted TigerStop feed tables.

One TABBR, sufficient for one leg set, contains two brackets, four binder rings, and a Table Hardware Pack (TABHP).  

Feed table hardware pack. You will need one hardware pack per section of table/leg set.   

The back fence ruler is a tape measure with an adhesive backing, frequently mounted to the back fence. BRLR  is 12 feet long, reads left to right, and displays measurements in inches, increasing to the right. (Tick marks show measurements as small as 1/16".)  

The Back Fence Ruler attaches to the Back Fence and is often used during the Backboard Optimization process seen below. 

Table leg ring bracket. PC hammertone black 39/80005.

One orange table leg bracket. Does not include hardware. 

Tabletop 14.4" deep x 6' long, Solid PC hammertone black 39/80005.  

The Chop Saw Support fits 14.4" wide tables only and accommodates a saw up to 24" deep and up to 29.9" wide. The Chop Saw Support comes with 2 table legs & hardware for easy installation. 

FREE GROUND SHIPPING DOES NOT APPLY. SHIPPING RATES WILL BE CALCULATED AND COLLECTED AFTER THE ONLINE ORDER IS PLACED TO GUARANTEE THE LOWEST FREIGHT RATE POSSIBLE. EMAIL ORDERS@TIGERSTOP.COM WITH ANY QUESTIONS.

The back fence ruler is a tape measure with an adhesive backing, frequently mounted to the back fence. The back fence ruler is a tape measure with an adhesive backing, frequently mounted to the back fence. BRRL is 12 feet long, reads right to left, and displays measurements in inches. (Tick marks show measurements as small as 1/16".)  

Saw Support Attachment Bracket.  

Chop saw support side plate for 14.4" tables.  

The Chop Saw Support for tilted tables fits 14 inch wide 10 degree tilted tables only and accommodates a saw up to 24" deep and up to 29.9" wide. The Chop Saw Support for tilted tables comes with 2 table legs & hardware for easy installation. 

FREE GROUND SHIPPING DOES NOT APPLY. SHIPPING RATES WILL BE CALCULATED AND COLLECTED AFTER THE ONLINE ORDER IS PLACED TO GUARANTEE THE LOWEST FREIGHT RATE POSSIBLE. EMAIL ORDERS@TIGERSTOP.COM WITH ANY QUESTIONS.

The SawGear portable table brackets allow the portable tables to attach to nearly any chop saw or chop saw stand. The brackets are included with the portable tables. Repacement part only. Hardware kit is included.    

The Back Fence Ruler is a tape measure with an adhesive backing, frequently mounted to the Back Fence (BF). BRRLM is 4 meters long and displays measurements in cm, increasing to the left. (Tick marks show measurements as small as 1 mm.) The Back Fence Ruler is often used during the Backboard Optimization process. 

The Back Fence Ruler is a tape measure with an adhesive backing, frequently mounted to the Back Fence (BF). BRLRM is 4 meters long and displays measurements in cm, increasing to the right. (Tick marks show measurements as small as 1 mm.)  

These brackets attach the legs to the table for all tilted TigerStop feed tables. They are incompatible with SawGear tables and with flat TigerStop feed tables.

One TABBR-T, sufficient for one leg set, contains two brackets, four binder rings, and a table hardware pack.