Products

The Idle End Cap is a plate that covers the end of the TigerStop extrusion that is far from the motor.  

The Idle End Carriage/Far End Carriage is for TigerStops using a 32mm (1.26") width belt. It contains the idle pulley, the pulley housing, and the tensioning bolt. 

Learn more about the Idle End Carriage in the below video.  

The idle end pulley is for TigerStops using a 32mm (1.26") width belt. It is compatible with the Idle End Carriage (IEC2).

Important Information About Ordering This Part:  

• The IEP is not compatible with Idle End Carriages that were manufactured prior to 2016.
• The IEP  will not work in place of the older flanged Idle End Pulley.
• If you are not sure about whether the IEP is compatible with your current Idle End Carriage please email service@tigerstop.com to confirm prior to ordering this part. 

This plug is used to connect a six-conductor cable with the six-pin I/O port on the amplifier. Soldering tools and ability will be required.

Interlock kill line bracket.   

The internal carriage connects the TigerStop belt inside the beam to the flip away outside of the beam. Ships assembled with Polymer Linear Guides (PLG). 

The IO panel interfaces with peripheral devices including barcode scanners, printers, clamps, and Standard Interconnect Kits (SIK). The IO Panel can be used with TigerStop, TigerFence (and SLR), TigerCrossCut, TigerTurbo, TigerRack, and HeavyDuty 2. The IO panel is compatible with the Controller (CON5) and Amplifier (AMP6), and cannot be used with older electronics.  This part ships with a 10-foot (3.0 m) version 5 controller cable (CC5-10).  

Please note the following about ordering this item:  

• IO panel orders require the serial number of the machine that will receive the electronics. Please send this information to orders@tigerstop.com. This IO Panel cannot be shipped otherwise.   
• Failure to use the IO panel with the specified serial number can result in software compatibility issues. Learn how to locate your serial number in the below video.  
• If you still have questions about ordering this part, please contact service@tigerstop.com for further information. 

The keypad membrane is compatible with the Version 5 Controller (CON5) and cannot be used with older electronics.

Watch our video for instructions about how to easily change our your keypad membrane. 

This keypad membrane is for controller versions 3.0-4.7, and is incompatible with the Version 5 Controller (CON5). Membrane dimensions are 9.25 by 5.0 inches (23.5 by 12.7 cm). 

This is a direct transfer printer for systems that are already enabled for printing. To add printing to an existing system, contact TigerStop customer service: service@tigerstop.com. The data cable and a roll of 4 by 2.5 inch (10.2 by 6.4 cm) labels are included.  Consumable printer ribbons are not required for direct thermal printing.    

NOTE: This printer must work in conjunction with a TigerTouch Tablet Package #TABLET-PKG. You may purchase a full Printer + Tablet Package here: #TABLET-PRINT-PKG.  Printer does not include a printer stand (PRTCVR), must be used with TigerTouch Tablet Package or SawGear Touch and PR0 enable code.

Label Printer Cable Assembly ,DB9 male to DB9 male, 12' Zebra printer.

This package includes a direct transfer label printer, printer stand (PRTCVR), and the printing enable code PR0. NOTE: Does not include a TABLET-PKG and must be used with one OR SawGear Touch and TigerStop tables.

To add printing to an existing system, contact TigerStop customer service: service@tigerstop.com. The data cable and a roll of 4 by 2.5 inch (10.2 by 6.4 cm) labels are included.  Consumable printer ribbons are not required for direct thermal printing.    

NOTE: This printer must work in conjunction with a TigerTouch Tablet Package #TABLET-PKG. You may purchase a full Printer + Tablet Package here: #TABLET-PRINT-PKG. 

Printer stand for label printers. The printer stand can be purchased separately, but does come with the Printer Package #TABLET-PRINT-PKG.   

Lead Screw square nut, with shoulders and tension slit.  

This roller switch is used in the Standard Interconnect Kit. It is also used as an end-sensor for the TigerFence, TigerCrossCut, TigerRack, TigerTurbo, and HeavyDuty 2.       

Linear guide bearing Rail 15mm x 230mm(dim E) EG bottom-mount